cubikitty
Start designing
Total$0
Modular cat towers

Designed by you,
made for them.

cubikitty towers are made from soft fabric cubes on wooden corner rods, plus posts, scratch ramps and perches that bolt together however you like. Design yours in 3D, then change it whenever your cat gets bored.

Design

Design in three easy steps

The designer runs right in your browser. No sign-up, nothing to download.

1

Pick a base

Start with one to six felt-covered plywood tiles and choose the footprint: a single tile, a corner, an L, a C-shape, or the full 2 × 3.

2

Drag in pieces

Add soft cubes with one to four doorways, scratching posts, scratch ramps, hammocks, cushion beds and dangling toys. Click any piece to move, recolor or remove it.

3

Review & save

See every part and the total, then save your build as a code so you can come back and keep tweaking.

Or start from one of our designs

About cubikitty

A cat tower that works like building blocks

cubikitty is a modular system. Everything sits on a base of 3/8" plywood tiles with a felt top. Each cube is a soft fabric sleeve stretched around four wooden corner rods, under a plywood top that carries the next level. That keeps a tower light, quick to ship and easy to change.

Cubes are 14" on each side, and the sleeve comes with one, two, three or four doorways. Every top and base tile has the same pattern of screwholes: corners for cube rods, an inner set for scratching posts, and a pair in the middle of each side for perches, ramps, hammocks and toys. Almost everything simply screws on.

Need to replace a part, or want to grow your tower? You can also order individual pieces for the cubes you already have: a new post, a fresh perch, one more cube.

14" cubesone size that snaps to one grid
1–6 tilesbase footprints from a single tile to 2 × 3
One patternthe same screwholes on every top and base tile
Fabric + woodsoft sleeves on a light wooden frame
Who we are

Engineers who love cats

We are a married couple of engineers who built our cats their own trees after noticing that they each had their spot, and wanted to share our ideas with others. cubikitty was our answer.

Personal to your cat

Pick the base, the pieces and the colors, and build the tower your cat loves to be in.

Made to be rearranged

Start small, add a level next month, move the hammock when your cat has opinions.

Soft where it counts

Fabric cubes, rounded edges and quiet materials that look at home in a living room.

5%
Our mission

Every tower helps a cat still waiting for a home

We donate 5% of proceeds to local animal shelters, so every cubikitty tower can help a cat without a home.

Featured cats

The cats behind cubikitty

Meet the testers, critics and nap experts who inspire every tower.

Two orange and white cats, Mi and Mosa, sharing a cat tree perch
Mi & MosaMi on the right, Mosa on the left.
Arty, a black and white tuxedo cat, lounging in a cat tree bed
ArtyThe Chonk
Jenkins, a black cat, looking into the camera
JenkinsThe Wizard Himself
FAQ

Questions, answered

How does the designer work?

Pick a base, then drag pieces onto it. Pieces snap to a grid, and you can rotate them with the R key, click a placed piece to move it, and undo or redo as you go. You can also start from one of our ready-made designs.

How tall can my tower be?

Height depends on the base: bases of one or two tiles go up to 3 levels, three tiles up to 4, four or five tiles up to 5, and the full six-tile base up to 6 levels of 14".

What are cubikitty towers made of?

A 3/8" plywood base with a felt top. Cubes are a sturdy fabric sleeve on four wooden corner rods with a plywood top. Posts and scratch ramps are covered in sisal.

Can I change my cubikitty tower after it's been built?

That's the idea. Pieces connect through screwholes, so you can add, swap or move parts later. Fabric sleeves come off, so you can change a cube's color or doorways without replacing its frame.

How do I save my design?

Your design is saved automatically in your browser. For a copy you can keep or share, use the code on the review step and paste it into "Have a build code?" any time.

How much does a cubikitty cost and how can I order one?

The designer shows a running total as you build. Each piece is priced on its own, so a tower costs what its pieces add up to. Ordering is coming soon; check back here for the latest. 5% of proceeds are donated to local animal shelters.

Start designing

Piece collection

Every piece, and how it mounts

cubikitty is built on one grid and two kinds of joint. This page is the working spec: what each piece is, what it attaches to, and the hardware that holds it. Dimensions are nominal.

Draft spec. These are design targets for prototyping. Hardware sizes, rod diameter and load ratings still need to be confirmed by building and load-testing real parts. A frame of rods can lean sideways, so stiffness under a jumping cat is the first thing to test.

The system

The grid

The soft cube

A cube is three parts: four corner rods, a fabric sleeve, and a plywood top. It has no floor and no rigid walls. The rods carry the weight, the top is the floor of the next level, and the sleeve makes the walls and doorways.

top: 14 × 14", 3/8"sleeve, 1 to 4doorwaysrod: 1" doweltop of piece below
Front view of a one-doorway cube standing on the piece below.
upper rod(insert in its foot)lower rod(stud in its top) plywood top, felt upstudfabric sleeve
Section through one corner: the lower rod's stud comes up through the top and the upper rod screws onto it.

Joint 1: screw-on rods and posts (block on block)

Rods and posts have a threaded insert in the foot and a stud in the top. To build up, screw a stud into each hole you need, then screw the rods or posts down onto them. The top drops over the studs on the rod tops, and the next level's rods screw on above it, clamping the top between them. Cube rods use the four outer corner holes; scratching posts use the inner corners or the center. At the top of a stack, cap nuts hold the last top down.

Joint 2: the side pair (accessories)

Each side of a top has one mounting spot: two 1/4"-20 T-nuts, 4-1/4" apart and 3/4" in from the edge, pressed in from underneath. A ramp's landing ledge and the two rails of a rail bridge line up with both holes, so each end takes two bolts. A ledge perch uses both. A hammock bridge hangs from an eye bolt in each. A toy screws into either one. One accessory per side.

The standard hole pattern

Every 14" top and every base tile has the same 17 holes. Each has one job, and almost every piece screws straight onto them:

4 outer corners: cube rods, plates 4 inner corners: scratch posts 1 center: single big posts 8 side holes, in pairs:ramps, bridges, perches, toys
Top view of a 14" top or base tile.
  • 4 outer corners: cube rods and the hammock perch deck.
  • 4 inner corners (on an 8-1/2" square): the four-post frame, three-post corner, and the round plates of beds.
  • 1 center: the single post and the sisal tower.
  • 8 side holes (a pair per side): ramps, bridges, perches and toys.

A scratch ramp's foot plate is slotted to catch whichever two holes fall under it.

1/4"-20 button-head bolt, 5/32" hex keyaccessory flangeT-nut, from belowpanel (1/2" recommended) + felt insert centre 3/4" in from the edge
Section through a screwhole point with an accessory flange bolted down.
landing ledge, 3"hook lugbolt intoscrewhole After: ledge sits flat on the top,lug hooks the edge, bolt holds it
A ramp end on a screwhole point: the landing ledge is the flange.

The landing ledge (ramps and rigid bridges)

Each end of a ramp carries a flat landing ledge, 2-1/4" deep and as wide as the ramp, fixed to the plank at the angle for that ramp size. The ledge sits flat on the top of the block and takes the weight. On the upper end, a hook lug under the ledge drops over the block's outer edge so the ramp cannot slide off, and bolts through the ledge go into the screwhole point.

Blocks

PieceSizeSits onTakes a block on topMounting notes
14" soft cubes (1, 2, 3 or 4 doorways)14 × 14 × 14"Base tile or any 14" topYesFour rods, one sleeve, one top. Rods thread onto the four corner studs below.
Sisal tower14 × 14 × 14"Base tile or any 14" topYesA 9-1/4" sisal-covered drum with a threaded core. It screws onto the center stud, and its top screws on above. Two pins into the inner corner holes stop it turning.
Post & platform14 × 14 × 14"Base tile or any 14" topYesOne 3" sisal-covered post that screws onto the center stud. Its top screws onto the post, and takes the standard hole pattern.
Four-post frame, Three-post corner14 × 14 × 14"Base tile or any 14" topYesEach sisal post screws onto an inner corner hole. The top screws onto the post tops.
Scratch ramps (long, steep, low, full)7 or 14" wide; 7 or 14" riseBase tile or any flat topNoSisal-faced plank on a foot plate and back leg. The foot plate bolts down. Nothing mounts to the slope.

Beds and perches

PieceSizeMounts toHow
Cushion bed13" roundTop of any 14" blockA round plate the same size as the bed. On a scratch post it screws straight onto the post or posts and replaces the square top, so no corners stick out. On a cube it bolts down to the inner corner holes of the cube's top. Caps the stack.
Cat-ear cave13" round base, 14" tallTop of any 14" blockA soft dome on the same round plate, mounted the same way as the cushion bed. Caps the stack.
Ledge perch14" wide × 6" deep shelfOne side of a 14" cube or post, at its top edgeA mounting flange lies on the top and takes two bolts into that side's pair. Two gussets under the shelf bear on the rods.
Round hammock perch14 × 14 × 7" deck plus an 11" hammock overhangTop of a 14" cube or postIts four short posts screw onto the outer corner studs, and the deck screws onto them. The hammock rim is fixed to the deck edge, and two angled arms brace the rim back to the feet of the posts. Needs the neighboring space on the hammock side to be empty.

Ramps and bridges

These span between two screwhole points. Because the points sit on the grid, every span comes out as one of a small set of lengths, so each connector is made in fixed sizes. A ramp or beam can run level or climb. Bridges run level only.

across 18" up one25-1/2" same heightone level up, one gap over side views: one square = one 14" block
Across a gap, and up one level over a gap.
kitty-corner12-3/4" mid to mid across two gaps 36" top views
Kitty-corner between two blocks that touch at a corner, and across two gaps.

Standard span lengths (point to point)

Run (gaps over)LevelUp 1 (14")Up 2 (28")Up 3 (42")
1 gap (14")14"19-3/4"31-1/4"44-1/4"
2 gaps (28")28"31-1/4"39-5/8"50-1/2"
3 gaps (42")42"44-1/4"50-1/2"59-3/8"
Kitty-corner, mid to mid9-7/8"n/an/an/a

Maximum run is 42" and maximum climb is three levels. Kitty-corner applies to hammock, two-rail and slat bridges. Ramps and beams run square to the blocks.

The connectors

PieceSectionEnd fittingRuns
Ramp9" wide felt-topped plank with cleats every 2-3/4"Landing ledge both ends, 2-1/4" × 9". Two bolts per end, into the side pair. Hook lug on the upper end (both ends when level).Level or climbing
Scratch beam1-1/2" sisal-covered poleSaddle plate both ends, wide enough to take both holes of the side pair. Hook lug on the upper end.Level or climbing
Two-rail bridgeTwo 3/4" hardwood rails, 4-1/4" apartEach rail sits over one hole of the side pair. A small end plate ties the two rails together, one bolt per rail.Level; straight or kitty-corner
Slat bridge6" × 1-1/4" slats on two cordsLanding ledge both ends, two bolts into the side pair, hook lugs. Cords knot through the ledge.Level; straight or kitty-corner
Hammock bridgeFabric sling, widest in the middleEach end has two rings, one clipped to an eye bolt in each hole of the side pair, so the sling hangs from four points and cannot twist.Level; straight or kitty-corner

Toys

Every toy hangs from the same arm: a 4-1/4" wooden stick set at 45°, with a 1/4"-20 stud on its base that threads straight into any free screwhole point. The toy hangs from an eye at the tip, clear of the block. Toys swap by unhooking them from the eye.

ToyHangsNotes
Pom-pom, Felt mouse, Sisal ball, Bell chimeAbout 5" below the tipSingle cord.
Feather dangler, Ribbon tailsAbout 3" to 5" below the tipThree felt pieces on one knot.
Spring coilAbout 4" below the tipCoil with a ball on the end.

Hardware list

PartSpecUsed for
T-nut1/4"-20, pronged, zincAll 17 holes of every top and base tile
Threaded insert1/4"-20, for woodThe foot of every rod and post
Stud1/4"-20 × 2"Screwed into whichever holes a rod or post will sit on, and in the top of every rod and post
Cap nut1/4"-20Holding down the last top, and plates of posts, beds and decks
Button-head bolt1/4"-20 × 3/4"Accessories: perches, ledges, saddle plates, tile joining plates
Eye bolt1/4"-20Hammock bridge ends
Hex key5/32"The only tool; cap nuts go on by hand

One thread size across the whole system means any bolt in the bag fits any hole of the right depth.

Open the designer
Assembly guide

Putting your cubikitty tower together

Every cubikitty piece bolts to the one below with the same bolt and the same hex key. Once you have built one cube, you know how to build them all.

Open the designer

Before you start

Two people make it easier. One person can build a small tower alone. For anything three levels or taller, have a second person steady the tower while you bolt the upper pieces.

Build a cube

A cube is four corner rods, a fabric sleeve and a plywood top. It has no floor of its own: it stands on the base tile or on the top of the piece below.

  1. Screw on the rods. Thread the four rods down onto the four corner studs of the base tile or the top below. Hand-tight is enough for now.
  2. Slide on the cover. Pull the fabric cover down over the four rods, with the doorways facing the way you want them. It should be snug. The rod tops stand a little above the fabric.
  3. Add the top. Set the plywood top straight onto the four rod tops, felt side up, with the rod studs through its corner holes. The next level's rods thread on above it and clamp it down. On the last level, use the four cap nuts.
  4. Tighten. Twist each rod snug by hand, working around the four corners.

Snug, not forced. Start every bolt by hand so it goes in straight. If it resists in the first few turns, back it out and start again.

How other pieces connect

Scratching posts screw on the same way as cube rods: four-post and three-post frames onto the inner corner holes, and the single post and sisal tower onto the center hole. Their platform then screws onto the post tops. Beds sit on a round plate that bolts to the inner corner holes. Decks and scratch ramps have a plate that bolts down to the holes under it. Perches, ramps, bridges and toys bolt into the free screwholes along each top edge.

Build your tower

  1. Lay out the base. Arrange the base tiles felt side up in the shape of your design. Join neighboring tiles with bolts through the screwholes along their shared edges.
  2. Add the first level. Build each ground-level cube on its tile, and bolt down any posts. Check that doorways face the way your design shows before you add the tops.
  3. Work upward, one level at a time. Finish and bolt a whole level before starting the next. 14" pieces sit on the base or on another 14" piece.
  4. Top it off. Beds, caves and scratch ramps go on last. Nothing stacks on top of them.
  5. Attach perches and toys. A ledge perch bolts into the pair of screwholes in the middle of a side. Ramps and bridges use the same pair. A toy screws into either hole of a pair. The round hammock perch is a block of its own: bolt it onto the piece below like any other block. Its two angled support arms are already braced to its own corner posts. Toys bolt to a single screwhole.
  6. Hang ramps and hammock bridges. These span between two pieces. Bolt one end, then the other. Ramps and scratch beams run in a straight line, either level or between two heights. Hammock, two-rail and slat bridges run straight across or corner to corner at the same height.
  7. Final check. Go around the tower and give every bolt a last snug turn. Press on the top and each perch with your hand. Nothing should shift or wobble.

Changing your tower later

  1. Work from the top down. Remove toys, perches, ramps and bridges from the piece you want to change first.
  2. Unbolt and lift off. Take out the bolts and lift the piece away. For a cube, take off the top, then the sleeve, then the rods.
  3. Rebuild. Add the new piece the same way as before. To change only a cube's color or doorways, swap the sleeve and put the same top back.

Keep the hex key and any spare bolts somewhere you will find them again.

Safety and care

Missing a bolt or need a replacement piece? You can order individual pieces any time.